Waterproof Wago Connectors

Waterproof Wago Connectors

Waterproof wago connectors help you avoid costly downtime caused by moisture. They also eliminate the need for tape, heat shrink, and mastics. Simply lift the lever, insert the wire and close the lever.

Gelbox is a compact box prefilled with gel that provides IPX8 moisture protection for WAGO 221 and 2273 series connectors. It is a VDE-tested solution for low and extra-low voltage applications.

Compact design

The WAGO Gelbox is a compact, reliable and cost-effective solution for waterproof wago connectors protecting splicing connectors against moisture. The box is pre-filled with a silicone-free gel and meets IPX8 protection standards. It can be used in a wide range of voltage applications and is ideal for installation in junction boxes.

The risk of short circuit is primarily caused by moisture and humidity in junction boxes. Moisture can form in various ways, including condensation or rapid temperature changes. The risk is even higher in transitional periods, such as spring and autumn.

When the conductors in a junction box get wet, the current takes completely new paths, which can lead to a short circuit. This can be very dangerous. To protect against this, encapsulation is an important solution.

WAGO’s newest product, the Gelbox, can provide a high level of protection against moisture and humidity. It is available in a variety of sizes and can be combined with different WAGO splicing connectors. It is ideal for use in junction boxes in both low- and extra-low voltage applications.

Thanks to its compact design, the WAGO Gelbox can be accommodated in any distribution box. It can also be easily re-opened and quickly and reliably re-wired – an advantage over standard electronics encapsulation. This is especially important when expansion of the system is required. This can be done without removing the Gelbox, even when there are other splicing connectors connected.

Easy to install

Waterproof wago connectors are easy to install, eliminating the need for time-consuming measures like tape, heat shrink or mastics. You simply need to remove the protective cover, insert the wires and twist on the waterproof connector. Then, remove the protecting cover and test the connection with a voltage tester to ensure that it’s insulated.

Moisture is dangerous to electrical installations. If it comes into contact with electricity, a short circuit can occur quickly. This is why encapsulation is the usual proven short-circuit protection solution. WAGO has now developed an even quicker and simpler moisture protection solution – the Gelbox for multi-wire lever-nut connectors.

The Gelbox is a compact box pre-filled with silicone-free gel. It is available in different sizes and provides IPX8 levels of moisture protection for WAGO’s 221 series COMPACT lever connectors and 2273 series COMPACT push wire connectors (for conductor cross-sections up to 4 mm2). The system has been tested and certified by an independent laboratory according to the VDE standard EN 60998.

The Gelbox can be easily accommodated in any distribution box, and its housing style allows several connectors to be positioned next to each other without creating additional space. The Gelbox can also be re-opened and re-wired, a real advantage compared to conventional electronics encapsulation. This allows the installation to be expanded, and it can be reused in new installations if necessary.

Easy to re-wire

The WAGO Gelbox protects the electrical installation precisely where it matters – at the connection points waterproof power connector – without permanently encapsulating the distribution boxes. It is easy to re-wire and provides a higher degree of protection than conventional encapsulation. The Gelbox can be used in a variety of applications and is ideal for LED lighting because it allows the cable to remain outside the light. This allows for a greater number of connections and gives designers more design flexibility.

The Gelbox consists of a compact box pre-filled with silicone-free gel. It is available in different sizes and provides IPX8 levels of moisture protection for multi-wire lever-nut connectors. It is suitable for a wide range of low and extra-low voltage applications. It is also suitable for use in junction and distribution boxes, allowing you to create waterproofed electrical systems quickly, easily and reliably.

WAGO’s 221 series lever-nut wire splicing connectors make it simple to connect solid and stranded copper conductors in various diameters. They feature a transparent housing that lets you visually inspect strip length and complete insertion. Simply lift one lever, insert the conductor and close the lever again. Then, you can tighten the connectors to secure your connections. The lever-action makes them fast and easy to use, and they offer significant time savings compared to traditional wire nuts.

Excellent protection against moisture

Condensation, heavy rainfall or even a powerful water jet are all things that electricity does not like. These phenomena can cause moisture to form in junction boxes, which in turn leads to short circuits. These short-circuits are not always immediately detected, but they can damage the equipment and pose a fire hazard. Fortunately, these risks can be easily avoided with the help of waterproof connectors.

The Wago Gelbox offers an excellent solution to this problem, as it comes pre-filled with Gel and seals the splicing connectors immediately. This box offers an IPX8 protection level, which is ideal for use in a variety of low- and extra-low voltage applications. It also saves valuable time, as it eliminates the need for you to mix a liquid sealing compound and wait for it to dry. In addition, the Gelbox is label-free and can be stored indefinitely.

Unlike standard electrical connectors, waterproof connectors are engineered to resist harsh environmental conditions and prevent moisture ingress. This ensures that the components remain operational, reducing downtime and the risk of costly repairs. These connectors are perfect for a wide range of applications, including residential automation projects. They are also used in industrial settings to connect sensors, actuators and controllers. Their durability and tool-free installation make them a great choice for applications in energy and process technology, such as power plants. They are also popular in renewable energy projects, as they can withstand the toughest outdoor environments.